
; M7NC-1.ASM -- NCR DECISION MATE V overlay for MDM7xx.	07/01/84
;
; You will want to look this file over carefully. There are a number of
; options that you can use to configure the program to suit your taste.
;
; Edit this file for your preferences then follow the "TO USE:" example
; shown	below.
;
; Use the MDM7xx "SET" command to change the baudrate when desired.  It
; starts out at 300 baud when the program is first called up.
;
;
;	TO USE:	First edit this file filling in answers for your own
;		equipment.  Then assemble with ASM.COM or equivalent
;		assembler.  Then use DDT to overlay the the results
;		of this	program to the original .COM file:
;
;=============================================================================
;
;NOTE:	 The use of the MDMLNK.COM utility makes the following process much
;	 simpler.  You may want to use MDMLNK if it is available to you.
;
;=============================================================================
;
;		A>DDT MDM7xx.COM
;		DDT VERS 2.2
;		NEXT  PC
;		4A00 0100
;		-IM7xx-x.HEX		(note the "I" command)
;		-R			("R" loads in the .HEX file)
;		NEXT  PC
;		4A00 0000
;		-G0			(return	to CP/M)
;		A>SAVE 73 MDM7xx.COM	(now have a modified .COM file)
;
; =   =	  =   =	  =   =	  =   =   =   =   =   =   =   =   =   =   =   =
;
; 07/01/84 - Slight changes for MDM740		- Robert Flagg
;	     Renamed from M7DMV.ASM to avoid
;	     confusion with the Dynabyte Monarch
;	     overlay (M7DM-1.ASM)
; 05/30/84 - Renamed to M7DMV.ASM for use with
;	     NCR DMV				- Mark Stamos
; 11/11/83 - Renamed to M7HZ-1.ASM, no changes	- Irv Hoff	
; 07/27/83 - Renamed to work with MDM712	- Irv Hoff
; 02/17/83 - Modified MDM703CF to work with
;	     Heath/Zenith -100 series com-
;	     puters with 2661B I/O		- Irv Hoff
;
; =   =	  =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
BELL:		EQU	07H		;bell
CR:		EQU	0DH		;carriage return
ESC:		EQU	1BH		;escape
LF:		EQU	0AH		;linefeed
;
YES:		EQU	0FFH
NO:		EQU	0
;
;
MODDAT:		EQU	070H		;data port for NCR DMV
MODSTAT:	EQU	071H		;STATUS PORT
MODMODE:	EQU	072H		;MODE REGISTER PORT
MODCMD:		EQU	073H		;COMMAND PORT
WRITE:		EQU	004H		;ADDED TO PORT ADDR FOR WRITE
MODRCVB:	EQU	2		;BIT TO TEST FOR INPUT DATA
MODRCVR:	EQU	2		;modem receive ready
MODSNDB:	EQU	1		;bit to test for ready to send
MODSNDR:	EQU	1		;modem send ready bit
;
;
		ORG	100H
;
		DS	3	;(for  "JMP   START" instruction)
;
PMMIMODEM:	DB	NO	;yes=PMMI S-100 Modem			103H
AUTODIAL:	DB	NO	;yes=HAYES-type modem			104H
TOUCHPULSE:	DB	'T'	;T=touch, P=pulse (Smartmodem-only)	105H
CLOCK:		DB	20	;clock speed in MHz x10, 25.5 MHz max.	106H
				;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc.
MSPEED:		DB	1	;0=110 1=300 2=450 3=600 4=710 5=1200	107H
				;6=2400	7=4800 8=9600 9=19200 default
BYTDLY:		DB	0	;0=0 delay  1=10ms  5=50 ms - 9=90 ms	108H
				;default time to send character in ter-
				;minal mode file transfer for slow BBS.
CRDLY:		DB	0	;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H
				;default time for extra wait after CRLF
				;in terminal mode file transfer
NOOFCOL:	DB	5	;number of DIR columns shown		10AH
SETUPTST:	DB	YES	;yes=user-added Setup routine		10BH
SCRNTEST:	DB	YES	;Cursor control routine 		10CH
RETRY:		DB	NO	;yes=reset the error limit to try again 10DH
				;no=abort after 10 consecutive errors
BAKUPBYTE:	DB	NO	;yes=change any file same name to .BAK	10EH
CRCDFLT:	DB	YES	;yes=default to CRC checking		10FH
TOGGLECRC:	DB	YES	;yes=allow toggling of CRC to Checksum	110H
CONVRUB:	DB	YES	;yes=rub to backspace			111H
TOGGLERUB:	DB	YES	;yes=allow toggling rub to backspace	112H
ADDLF:		DB	NO	;no=no LF after CR to send file in	113H
				;terminal mode (added by remote echo)
TOGGLELF:	DB	YES	;yes=allow toggling of LF after CR	114H
TRANLOGON:	DB	NO	;yes=allow transmission of logon	115H
				;write logon sequence at location LOGON
SAVCCP:		DB	YES	;yes=do	not overwrite CCP		116H
LOCONEXTCHR:	DB	NO	;yes=local command if EXTCHR precedes	117H
				;no=external command if EXTCHR precedes
TOGGLELOC:	DB	YES	;yes=allow toggling of LOCONEXTCHR	118H
LSTTST:		DB	YES	;yes=printer available on printer port	119H
XOFFTST:	DB	NO	;yes=checks for XOFF from remote while	11AH
				;sending a file in terminal mode
XONWAIT:	DB	NO	;yes=wait for XON after CR while	11BH
				;sending a file in terminal mode
TOGXOFF:	DB	YES	;yes=allow toggling of XOFF checking	11CH
IGNORCTL:	DB	YES	;yes=CTL-chars above ^M not displayed	11DH
EXTRA1:		DB	0	;for future expansion			11EH
EXTRA2:		DB	0	;for future expansion			11FH
BRKCHR:		DB	'@'-40H	;^@ = Send a 300 ms. break tone 	120H
NOCONNCT:	DB	'L'-40H	;^L = Disconnect from the phone line	121H
LOGCHR:		DB	'N'-40H	;^N = Send logon			122H
LSTCHR:		DB	'P'-40H	;^P = TOGGLE PRINTER			123H
UNSAVE:		DB	'R'-40H	;^R = close text buffer			124h
TRANCHR:	DB	'T'-40H	;^T = Transmit file to remote		125H
SAVECHR:	DB	'Y'-40H	;^Y = Open input text buffer		125H
EXTCHR:		DB	'^'-40H	;^^ = Send next character		126H
;
;
		DS	2		;				128H
;
IN$MODCTL1:	IN	MODSTAT	! RET	;in modem control port		12AH
		DS	7
OUT$MODDATP:	OUT	MODDAT+4! RET	;out modem data port		134H
		DS	7
IN$MODDATP:	IN	MODDAT	! RET	;in modem data port		13EH
		DS	31
;
LOGONPTR:	DW	LOGON		;for user message.		160H
		DS	6		;				162H
JMP$GOODBYE:	JMP	GOODBYE		;				168H
JMP$INITMOD:	JMP	INITMOD		;go to user written routine	16BH
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	16EH
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	171H
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	174H
JMP$SETUPR:	JMP	SETUPR		;				177H
JMP$SPCLMENU:	JMP	SPCLMENU	;				17AH
JMP$SYSVER:	JMP	SYSVER		;				17DH
JMP$BREAK:	JMP	SENDBRK		;				180H
;
;
; Do not change the following six lines.
;
JMP$ILPRT:	DS	3		;				183H
JMP$INBUF	DS	3		;				186H
JMP$INLNCOMP:	DS	3		;				189H
JMP$INMODEM	DS	3		;				18CH
JMP$NXTSCRN:	DS	3		;				18FH
JMP$TIMER:	DS	3		;				192H
;
;
CLREOS:		CALL	JMP$ILPRT	;				195H
		DB	ESC,'Y',0,0,0	;				198H
		RET			;				19DH
;
CLRSCRN:	CALL	JMP$ILPRT	;				19EH
		DB	ESC,':',0,0,0	;CLEAR ENTIRE SCREEN		1A1H
		RET			;				1A6H
;
;
SYSVER:		CALL	JMP$ILPRT	;				1A7H
		DB	0BH,CR
		DB	'Version for NCR Decision Mate V with K211 interface'
		DB	CR,LF,0
		DB	RET
;.....
;
;
;-----------------------------------------------------------------------
;
; NOTE:	 You can change the SYSVER message to be longer or shorter.  The
;	 end of	your last routine should terminate by 0400H (601 bytes
;	 available after start of SYSVER) if using the Hayes Smartmodem
;	 or by address 0C00H (2659 bytes available) otherwise.
;
;-----------------------------------------------------------------------
;
; You can put in a message at this location which can be called up with
; CTL-O	if TRANLOGON has been set YES.	You can put in several lines if
; desired.  End with a 0.
;
LOGON:	  DB	'this is the place for your message',CR,LF,0
;.....
;	
;
; This routine allows a 300 ms. break tone to be send to reset some
; time-share computers.
;
SENDBRK:  MVI	A,1DH		;SEND A BREAK TONE FOR 300 MS.
	  JMP	GOODBYE1
;.....
;
;
; This routine sends a 300 ms. break tone and sets DTR low for the same
; length of time to disconnect some modems such as the Bell 212A, etc.
;
GOODBYE:  MVI	A,05H		;SET BREAK, DTR LOW
;
GOODBYE1: OUT	MODCMD+4	;PUT COMMAND REGISTER OUT OF MODE
	  IN	MODCMD		;MAKE SURE IT IS NOW CLEAR
	  IN	MODCMD		;TRY ONCE MORE
	  MVI	B,3		;DELAY FOR 300 MS.
	  CALL	JMP$TIMER
	  MVI	A,37H		;RESET RTS, FLAGS, DTR LOW, ENABLE R/T
	  OUT	MODCMD+4	;SEND TO COMMAND REGISTER
	  IN	MODCMD		;CLEAR ANY INCOMING CHARS.
	  IN	MODCMD		;TRY ONCE MORE
	  XRA	A		;CLEAR THE 'A' REG.
	  RET
;.....
;
;
; The following are used in setting up the 2651B I/O port.
;
INITMOD:  MVI	A,1		;DEFAULT TRANSFER TIME TO 300 BAUD
	  STA	MSPEED
	  XRA	A		;SET RTS, FLAGS, DTR, DISABLE R/T
	  OUT	MODCMD+4	;PUT COMMAND REGISTER OUT OF MODE
	  IN	MODCMD		;MAKE SURE IT IS NOW CLEAR
	  IN	MODCMD		;TRY ONCE MORE
	  MVI	A,4EH		;1 STOP, NO PARITY, 8 BITS, 16X ASYNCH
	  OUT	MODMODE+4	;SEND TO MODE REGISTER 1
;
INITMOD1: MVI	A,0F5H		;START WITH 300 BAUD, INTERNAL 5.0 CLOCK
	  OUT	MODMODE+4	;SEND TO MODE REGISTER 2
	  MVI	A,37H		;RESET RTS, FLAGS, DTR LOW, ENABLE R/T
	  OUT	MODCMD+4	;SEND TO COMMAND REGISTER
	  IN	MODCMD		;CLEAR ANY INCOMING CHARS.
	  IN	MODCMD		;TRY ONCE MORE
	  XRA	A		;CLEAR THE 'A' REG.
	  RET
;.....
;
;
; The following changes the baud rate with the SET command.
;
SETUPR:	  LXI	D,BAUDBUF
	  CALL	JMP$ILPRT
	  DB	'Input Baud Rate (110, 300, 1200, 9600): ',0
	  CALL	JMP$INBUF
	  LXI	D,BAUDBUF+2
	  CALL	JMP$INLNCOMP
	  DB	'110',0
	  JNC	OK110
	  CALL	JMP$INLNCOMP	;COMPARE BAUDBUF+2 WITH CHARACTERS BELOW
	  DB	'300',0
	  JNC	OK300		;GO IF GOT MATCH
	  CALL	JMP$INLNCOMP
	  DB	'1200',0
	  JNC	OK1200
	  CALL	JMP$INLNCOMP
	  DB	'9600',0
	  JNC	OK9600
	  CALL	JMP$ILPRT	;ALL MATCHES FAILED, ASK AGAIN
	  DB	'++ Incorrect entry ++',CR,LF,BELL,0
	  JMP	SETUPR		;TRY AGAIN
;
OK110:	  MVI	A,0		;MSPEED	110 BAUD VALUE
	  LHLD	BD110		;GET 110 BAUD PARAMETERS IN 'HL'
	  JMP	LOADBD		;GO LOAD THEM
;
OK300:	  MVI	A,1
	  LHLD	BD300
	  JMP	LOADBD
;
OK1200:	  MVI	A,5
	  LHLD	BD1200
	  JMP	LOADBD
;
OK9600:	  MVI	A,8
	  LHLD	BD9600
;
LOADBD:	  STA	INITMOD+1
	  MOV	A,L		;get least significant baud rate byte
	  STA	INITMOD1+1	;store in INITMOD1
	  JMP	INITMOD		;reset Z-100 2661
;.....
;
;
; TABLE	OF BAUDRATE PARAMETERS FOR 2661 I/O
;
BD110:	  DW	00F4H
BD300:	  DW	00F5H
BD1200:	  DW	00F7H
BD9600:	  DW	00FCH
;
BAUDBUF:  DB	10,0
	  DS	10
;
;-----------------------------------------------------------------------
;
; The following routine could be used to display selections of interest
; to owners of this computer.  If using the Hayes Smartmodem this is
; unavailable without a special change.
;
SPCLMENU: RET
;
;-----------------------------------------------------------------------
;
;
; NOTE:	 MUST TERMINATE PRIOR TO 0400H (with Smartmodem)
;				 0C00H (without Smartmodem)
;
	  END
;
