; MXMM-2.ASM
;
REV     EQU     20		;OVERLAY REVISION LEVEL
;
; MEX Micromodem II/IIe overlay for the APPLE II/II+/IIe;
;	written 09/04/84 by Joe Patterson (70235,460)
;		adapted from
;
; MEX Apple Super Serial Card / Novation J-Cat overlay
;	written 05/18/84 by D. W. Walker
;	ALS bank-switching adapted from
;	an overlay by James M. Scardelis
;
; Revn: 1.0  04 Sept 84 -- Modified MXO-AP.21 to produce this
;			    overlay.
;	2.0  09 SEPT 84 -- ADDED TOUCH-TONE DIALING FOR THE
;			   MICROMODEM IIE (ONLY)
;			-- RENAMED TO MXMM-2.ASM FROM MXO-MM10.ASM
;			-- ADDED CONTROL PORT 3 JUMP FOR THE
;			   SOFTCARD (COULD NOT USE MMIIE ON 
;			   SOFTCARD OTHERWISE)
;
;
; This overlay is for the MEX--- series of modem programs. It is
;   adapted from MXO-AP.21 to work with the APPLE II and the
;   Hayes Micromodem II and IIe with either the ALS CP/M CARD
;   or the Microsoft Softcard. Data format is 8 bits, no parity,
;   1 stop bit. If you have the Micromodem IIe then answer YES
;   to --BOTH-- equates MM and MM2e to turn the speaker on when
;   dialing and off when connected. If you have the Micromodem II
;   then you must --NOT-- answer yes to the MM2e equate as the
;   program will probably bomb out if you do.
;
; Revision 2.0 now supports touch-tone dialing on the Micromodem
;   IIe (ONLY) if you answer YES to the MM2E equate. When using
;   touch-tone, the comma (,) feature is supported. Inserting a
;   comma in the number being dialed, causes a 2 second delay for
;   each one used. For example, 555-12,34 causes dialing to pause
;   for 2 seconds between digits 2 and 3. This is especially useful
;   when waiting for an outside line or a second dial tone. Multiple
;   commas can be used.
;
; I have tested this overlay and it seems to work ok, but, if
;   anyone finds any let me know and I will try to correct them
;   as soon as possible.
;
;
; The SET WAIT command adjusts the time that the dialing
;   routines will wait for a connection (carrier), from
;   0 to 25 seconds.
; 
; NOTE: Most of the comments from Ron Fowler's MXO-PM10.ASM
;   have been omitted here to save space.  A copy of that file
;   will be very helpful in understanding what's going on here. 
;
;------------------------------------------------------------
;
; Misc equates
;
NO	EQU	0
YES	EQU	0FFH
TPA	EQU	100H
CR	EQU	13
LF	EQU	10
BELL	EQU	7
TAB	EQU	9
ESC	EQU	27
;	  
MM	EQU	YES	;YES FOR HAYES MICROMODEM II
MM2E	EQU	YES	;YES FOR MM2E ONLY (FOR TOUCH-TONE & SPEAKER)
			;MUST BE NO IF YOU HAVE THE MICROMODEM II
SFTCRD	EQU	NO	;YES for Microsoft Softcard } choose
ALSCRD	EQU	YES	;YES for ALS CP/M+ card     } one only
; 
	IF SFTCRD
POFF	EQU	2000H	;Softcard address offset
RATE	EQU	20
	ENDIF
;
	IF ALSCRD
POFF	EQU	0
RATE	EQU	60
	ENDIF
;
	IF	MM
SLOT	EQU	20H		;SLOT FOR MICROMODEM X 10
PORT    EQU	0C086H+POFF+SLOT  ;BASE CTL/STAT PORT FOR MM
MODDAT	EQU	PORT+1		;MM DATA PORT
MODSTT	EQU	PORT		;MM STATUS PORT
MODCTL	EQU	PORT		;MM CTL PORT 1
BAUDRP	EQU	PORT-1		;MM CTL PORT 2
MODCTL3:EQU	PORT-3		;MM2e CONTROL PORT 3
;
;
MDRCVB	EQU	01H	;MM RECIEVE BIT
MDRCVR	EQU	01H	;MM RECIEVE READY BIT
MDSNDB	EQU	02H	;MM SEND BIT
MDSNDR	EQU	02H	;MM SEND READY BIT
;
DTR     EQU	8FH		;TRANS ENABLE, ORIG., 300 BAUD
OFFHK	EQU	80H		;OFF-HOOK
ONHK	EQU	0		;ON-HOOK
SPKRON	EQU	00100000B	;MMIIe SPEAKER ON
SPKROFF EQU     00000000B	;MMIIe SPEAKER OFF
;
CTSMSK	EQU	00000000B	  ;MASK TO TEST FOR CARRIER
BRKMSK	EQU	60H		  ;MASK TO SET BREAK
ONHOOK	EQU	0C085H+POFF+SLOT  ;ADDRESS FOR ONHOOK SET
OFFHOOK EQU	ONHOOK            ;OFFHOOK ADDRESS
	ENDIF	;MM
;
;
;
; MEX service processor stuff ... See MXO-PM10.ASM
;
MEX	EQU	0D00H		;address of the service processor
INMDM	EQU	255		;get char from port to A, CY=no more in 100 ms
TIMER	EQU	254		;delay 100ms * reg B
TMDINP	EQU	253		;B=# secs to wait for char, cy=no char
CHEKCC	EQU	252		;check for ^C from KBD, Z=present
SNDRDY	EQU	251		;test for modem-send ready
RCVRDY	EQU	250		;test for modem-receive ready
SNDCHR	EQU	249		;send a character to the modem (after sndrdy)
RCVCHR	EQU	248		;recv a char from modem (after rcvrdy)
LOOKUP	EQU	247		;table search: see CMDTBL comments for info
PARSFN	EQU	246		;parse filename from input stream
BDPARS	EQU	245		;parse baud-rate from input stream
SBLANK	EQU	244		;scan input stream to next non-blank
EVALA	EQU	243		;evaluate numeric from input stream
LKAHED	EQU	242		;get nxt char w/o removing from input
GNC	EQU	241		;get char from input, cy=1 if none
ILP	EQU	240		;inline print
DECOUT	EQU	239		;decimal output
PRBAUD	EQU	238		;print baud rate
;
;
CONOUT	EQU	2		;simulated BDOS function 2: console char out
PRINT	EQU	9		;simulated BDOS function 9: print string
INBUF	EQU	10		;input buffer, same structure as BDOS 10
;
	ORG	TPA		;we begin
;
;
	DS	3		;MEX has a JMP START here
;
; The following variables are located at the beginning of the program
; to facilitate modification without the need of re-assembly. They will
; be moved in MEX 2.0.
;
PMODEM:	DB	YES		;yes=PMMI modem \ / These 2 locations are not
SMODEM:	DB	NO		;yes=Smartmodem / \ referenced by MEX
TPULSE:	DB	'P'		;T=touch, P=pulse (not referenced by MEX)
CLOCK:	DB	RATE		;clock speed x .1, up to 25.5 mhz.
MSPEED:	DB	1		;sets display time for sending a file
				;0=110	1=300  2=450  3=600  4=710
				;5=1200 6=2400 7=4800 8=9600 9=19200
BYTDLY:	DB	5		;default time to send character in
				;terminal mode file transfer (0-9)
				;0=0 delay, 1=10 ms, 5=50 ms, 9=90 ms
CRDLY:	DB	3		;end-of-line delay after CRLF in terminal
				;mode file transfer for slow BBS systems
				;0=0 delay, 1=100 ms, 5=500 ms, 9=900 ms
COLUMS:	DB	5		;number of directory columns
SETFL:	DB	YES		;yes=user-defined SET command
SCRTST:	DB	YES		;yes=if home cursor and clear screen
				;routine at CLRSCRN
	DB	0		;was once ACKNAK, now spare
BAKFLG:	DB	NO		;yes=make .BAK file
CRCDFL:	DB	YES		;yes=default to CRC checking
				;no=default to Checksum checking
TOGCRC:	DB	YES		;yes=allow toggling of Checksum to CRC
CVTBS:	DB	NO		;yes=convert backspace to rub
TOGLBK:	DB	YES		;yes=allow toggling of bksp to rub
ADDLF:	DB	NO		;no=no LF after CR to send file in
				;terminal mode (added by remote echo)
TOGLF:	DB	YES		;yes=allow toggling of LF after CR
TRNLOG:	DB	NO		;yes=allow transmission of logon
				;write logon sequence at location LOGON
SAVCCP:	DB	YES		;yes=do not overwrite CCP
LOCNXT:	DB	NO		;yes=local cmd if EXTCHR precedes
				;no=not local cmd if EXTCHR precedes
TOGLOC:	DB	YES		;yes=allow toggling of LOCNXTCHR
LSTTST:	DB	YES		;yes=allow toggling of printer on/off
				;in terminal mode. Set to no if using
				;the printer port for the modem
XOFTST:	DB	NO		;yes=allow testing of XOFF from remote
				;while sending a file in terminal mode
XONWT:	DB	NO		;yes=wait for XON after sending CR while
				;transmitting a file in terminal mode	
TOGXOF:	DB	YES		;yes=allow toggling of XOFF testing
IGNCTL:	DB	YES		;yes=do not send control characters
				;above CTL-M to CRT in terminal mode
				;no=send any incoming CTL-char to CRT
EXTRA1:	DB	0		;for future expansion
EXTRA2:	DB	0		;for future expansion
BRKCHR:	DB	'@'-40H		;^@ = Send a 300 ms. break tone
NOCONN:	DB	'N'-40H		;^N = Disconnect from phone line
LOGCHR:	DB	'L'-40H		;^L = Send logon
LSTCHR:	DB	'P'-40H		;^P = Toggle printer
UNSVCH:	DB	'R'-40H		;^R = Close input text buffer
TRNCHR:	DB	'T'-40H		;^T = Transmit file to remote
SAVCHR:	DB	'Y'-40H		;^Y = Open input text buffer
EXTCHR:	DB	'^'-40H		;^^ = Send next character
;
	DS	2
;
INCTL1:	CALL	XSTTIN		;in modem status port
	RET
	DB	0,0,0,0,0,0	;spares if needed
;		    
OTDATA:	CALL	XDATOUT		;out modem data port
	RET
	DB	0,0,0,0,0,0	;spares if needed
;
INPORT:	CALL	XDATIN		;in modem data port
	RET
	DB	0,0,0,0,0,0	;spares if needed
;
MASKR:	ANI MDRCVB ! RET	;bit to test for receive ready
TESTR:	CPI MDRCVR ! RET	;value of receive bit when ready
MASKS:	ANI MDSNDB ! RET	;bit to test for send ready
TESTS:	CPI MDSNDR ! RET	;value of send bit when ready
;
;
	DS	12
;
;
LOGON:	DS	2		;needed for MDM compat, not ref'd by MEX
DIALV:	JMP	PDIAL		;dial digit in A (see info at PDIAL)
DISCV:	JMP	PDISC		;disconnect the modem
GOODBV:	JMP	DUMMY		;called before exit to CP/M
INMODV:	JMP	NITMOD		;initialization. Called at cold-start
NEWBDV:	JMP	PBAUD		;set baud rate
NOPARV:	DS	3		;set modem for no-parity
PARITV:	DS	3		;set modem parity
SETUPV:	JMP	SETCMD		;SET cmd: jump to a RET if you don't write SET
SPMENV:	DS	3		;not used with MEX
VERSNV:	JMP	SYSVER		;Overlay's voice in the sign-on message
BREAKV:	JMP	PBREAK		;send a break
;
;
ILPRTV:	DS	3		;replace with MEX function 9
INBUFV:	DS	3		;replace with MEX function 10
ILCMPV:	DS	3		;replace with table lookup funct. 247
INMDMV:	DS	3		;replace with MEX function 255
NXSCRV:	DS	3		;not supported by MEX (returns w/no action)
TIMERV:	DS	3		;replace with MEX function 254
;
CLREOS:	LXI	D,EOSMSG
	MVI	C,PRINT
	CALL	MEX
	RET
;
CLS:	LXI	D,CLSMSG
	MVI	C,PRINT
	CALL	MEX
	RET
;
;------------------------------------------------------------
;
;	*** END OF FIXED FORMAT AREA ***
;
;------------------------------------------------------------
;
; MICROMODEM AND ALS CARD INITIALIZATION
;
NITMOD:	
	IF ALSCRD
	LHLD	1		;get WBOOT vector
	LXI	D,60H		;offset for 32 entries
	DAD	D		;BIOS "read Apple address"
	SHLD	AR0+1		;patch read vector
	INX	H
	INX	H
	INX	H		;BIOS "write Apple address"
	SHLD	AW0+1		;patch write vector
 	ENDIF
 
;
	IF	MM
	MVI	A,03H
	CALL	XCTLOUT		;RESET MICROMODEM
	MVI	A,15H		;8 DATA BITS 1 STOP NO PARITY
	CALL	XCTLOUT
	RET
	ENDIF	;MM
;
; Micromodem send-break routine
;
PBREAK:	CALL	XCTLIN		;get control register
	PUSH	PSW		;save it
	ORI	BRKMSK		;set break bits
	CALL	XCTLOUT		;break line
	PUSH	B
	LXI	B,233		;wait 233 msec
	CALL	DELAY
	POP	B
	POP	PSW
	CALL	XCTLOUT		;restore control register 
	RET
;
; disconnect the Micromodem (and turn off MMIIe speaker)
;
PDISC:	PUSH	B
;
	IF	MM2E
	MVI	A,SPKROFF
	CALL	XCTL3		;SPEAKER OFF
	ENDIF			;MM2E
;
	MVI	A,ONHK
	CALL	XONHOOK		;hang up
	LXI	B,25		;for 25 msec
	CALL	DELAY
	MVI	A,OFFHK
	CALL	XOFFHK		;pick up again
	LXI	B,20		;for 20 msec
	CALL	DELAY
	MVI	A,ONHK
	CALL	XONHOOK		;hang up for good
	POP	B
	RET
;
; wait for BC milliseconds
;
DELAY:	PUSH	D
	INR	B
DELAY1:	LXI	D,3*RATE	;count for 1 msec
DELAY2:	DCX	D		;..may need some tweaking
	MOV	A,E
	ORA	D
	JNZ	DELAY2		;delay 1 msec
	DCR	C
	JNZ	DELAY1		;delay another
	DCR	B
	JNZ	DELAY1
	POP	D		;done, restore DE
	RET
;
; exit routine
;
DUMMY:	RET			;we don't need one
;
;
;------------------------------------------------------------
;
;   MICROMODEM DIALING ROUTINES (PULSE AND TOUCH-TONE)
;
;------------------------------------------------------------
;
PDIAL:	CPI	254		;start-dial?
	JZ	STDIAL
	CPI	255		;end-dial
	JZ	ENDIAL
;
	CPI	','		;SEE IF DIGIT IS ','
	JZ	DIALCM		;YES
	CPI	'9'+1		;digits are 0-9
	RNC			;too big...
	SUI	'0'
	RC			;too small....
	JNZ	DIALIT		;just right...
	MVI	A,10		;convert zero to 10 pulses
;
; Pulse phone "digit" times
;
	IF	NOT MM2E
DIALIT:	MOV	E,A		;save the digit
	PUSH	B
DIGLP:	MVI	A,ONHK
	CALL	XONHOOK
	LXI	B,65		;for 65 msec
	CALL	DELAY
	MVI	A,OFFHK
	CALL	XOFFHK		;connect line
	LXI	B,42		;for 42 msec
	CALL	DELAY
	DCR	E		;pulse again?
	JNZ	DIGLP		;yes, do it
	MVI	B,3		;300 MSEC BETWEEN DIGITS
	MVI	C,TIMER
	CALL	MEX
	POP	B		;no, exit
	RET
	ENDIF			;MM
;
;
	IF	MM2E
DIALIT: ADI     30H		;ADD 30H TO DIGIT TO KEEP SPEAKER -
	PUSH	B		;ON AND SEND TONE
DIGLP:  CALL    XCTL3		;SEND DIGIT
	LXI	B,120		;NUMBER OF MSEC FOR EACH TONE
	CALL	DELAY
	MVI	A,20H		;TURN OFF TONE
	CALL	XCTL3
	MVI	B,1		;100 MSEC BTWEEN DIGITS
	MVI	C,TIMER
	CALL	MEX
	POP	B
	RET
	ENDIF			;ENDIF MM2E
;
;
; THIS ROUTINE CONVERTS THE COMMA (,) TO IT'S MICROMODEM DECIMAL
;   EQUIVALENT. THE COMMA CAUSES A TWO (2) SECOND DELAY IN
;   DIALING BETWEEN ANY 2 DIGITS.
;
;
DIALCM: MVI	B,20		;DIGIT IS COMMA - SO WAIT 2 SEC.
	MVI	C,TIMER
	CALL	MEX
	RET
;
;
; END OF SPECIAL DIALING CONVERSION ROUTINE
;
;
; Start-dial sequence: connect, wait for dial-tone
;
STDIAL:	CALL	ILPRT
	DB	'Wait...',0
	MVI	B,25		;wait 2.5 sec
	MVI	C,TIMER
	CALL	MEX
	MVI	A,DTR		;enable modem
	CALL	XBDOUT
	;
	IF	MM2E
	MVI	A,SPKRON
	CALL	XCTL3		;TURN ON MMIIE SPEAKER
	ENDIF			;MM2E
	;
	MVI	A,OFFHK
	CALL	XOFFHK		;connect phone
	MVI	B,20		;wait 2 sec
	MVI	C,TIMER
	CALL	MEX		;for dial tone
	ORA	A
	RET
;
; End-dial sequence
;
ENDIAL: MVI	E,150		;SET WAIT TIME TO 15 SEC.
	MVI	A,8DH		;ENABLE MODEM (OFF-HOOK,ORIG.,300 BD)
	CALL	XBDOUT
WAITTM	EQU	$-1		;patch with SET WAIT command
	CALL	WAIT
	ORA	A		;successfully connected?
	PUSH	PSW		;save the error code
	JNZ	NOTCNK		;no, disconnect
	MVI	A,DTR
	CALL	XBDOUT		;RE-ENABLE MODEM
	;
	IF	MM2E
	MVI	A,SPKROFF	;MMIIE SPEAKER OFF
	CALL	XCTL3
	ENDIF			;MM2E
	;
	JMP	DIALXIT	
NOTCNK:	CALL	PDISC		;shut down the modem
DIALXIT:POP	PSW
	RET
;
; Time-out routine.  Must be called with mask in D reg.
; and number of seconds (times 10) in E reg.
;
WAIT:	MVI	B,1		;100 ms
	MVI	C,TIMER	
	CALL	MEX
	CALL	XDATIN		;READ DATA PORT (SET-UP CARR. DET.)
	CALL	XSTTIN		;IS CARRIER LOST SINCE LAST DATA READ?
	ANI	4		;4=NO CARRIER, 0=CARRIER
	RZ			;active low, so return on 0
	MVI	C,CHEKCC	;not yet, check for console-abort
	CALL	MEX		;abort?
	MVI	A,3		;set error code 3 if abort active
	STC
	RZ			;return if aborted
	DCR	E		;nope, downcount
	JNZ	WAIT
	DCR	A		;set error=2 (timed out); cy already set
	RET
 
;------------------------------------------------------------
;	END OF MICROMODEM DIALING ROUTINES
;------------------------------------------------------------
;
; Only 300 baud is supported for the Micromodem
;
;
	IF 	MM
PBAUD:	RET
	ENDIF	;MM
;
;
; Control is passed here after MEX parses a SET command.
;
SETCMD:	MVI	C,SBLANK	;any arguments?
	CALL	MEX
	JC	SETSHO		;if not, go print out values
	LXI	D,CMDTBL	;parse command
	CALL	TSRCH		;from table
	PUSH	H		;any address on stack
	RNC			;if we have one, execute it
	POP	H		;nope, fix stack
SETERR:	LXI	D,SETEMS	;print error
	MVI	C,PRINT
	CALL	MEX
	RET
;
SETEMS:	DB	CR,LF,BELL,'SET command error',CR,LF,'$'
;
; SET command table ... note that tables are constructed of command-
; name (terminated by high bit=1) followed by word-data-value returned
; in HL by MEX service processor LOOKUP.  Table must be terminated by
; a binary zero.
;
; Note that LOOKUP attempts to find the next item in the input stream
; in the table passed to it in HL ... if found, the table data item is
; returned in HL; if not found, LOOKUP returns carry set.
;
CMDTBL:	DB	'?'+80H			;"set ?"
	DW	STHELP
	DB	'BAU','D'+80H		;"set baud"
	DW	STBAUD
	DB	'WAI','T'+80H		;"set wait time"
	DW	STWAIT
	DB	0		;<<=== table terminator
;
; SET <no-args>: print current statistics
;
SETSHO:	CALL	CARRSH		;show carrier present/not present
	LXI	H,SHOTBL	;get table of SHOW subroutines
SETSLP:	MOV	E,M		;get table address
	INX	H
	MOV	D,M
	INX	H
	MOV	A,D		;end of table?
	ORA	E
	RZ			;exit if so
	PUSH	H		;save table pointer
	XCHG			;adrs to HL
	CALL	GOHL		;do it
	CALL	CRLF		;print newline
	MVI	C,CHEKCC	;check for console abort
	CALL	MEX
	POP	H		;it's done
	JNZ	SETSLP		;continue if no abort
	RET
;
GOHL:	PCHL
;
; table of SHOW subroutines
;
SHOTBL:	DW	BDSHOW
	DW	WTSHOW
	DW	0		;<<== table terminator
;
; SET ?  processor
;
STHELP:	LXI	D,HLPMSG
	MVI	C,PRINT
	CALL	MEX
	RET
;
; The help message
;
HLPMSG:	DB	CR,LF,'SET command, MICROMODEM II/IIE version:',CR,LF
	DB	CR,LF,TAB,'ONLY 300 BAUD SUPPORTED'
	DB	CR,LF,TAB,'SET WAIT 0..25'
	DB	CR,LF,'$'
;
; SET BAUD processor
;
STBAUD:	MVI	C,BDPARS	;function code
	CALL	MEX		;let MEX look up code
	JC	SETERR		;invalid code
	CALL	PBAUD		;no, try to set it
	JC	SETERR		;not-supported code
BDSHOW:	CALL	ILPRT		;display baud
	DB	'Baud rate: ',TAB,0
	LDA	MSPEED
	MVI	C,PRBAUD	;use MEX routine
	CALL	MEX
	RET	      
;
; SET WAIT processor
;
STWAIT:	MVI	C,EVALA		;get new time from input
	CALL	MEX
	MOV	A,H		;check for valid input
	ORA	A
	JNZ	SETERR
	MOV	A,L
	CPI	26
	JNC	SETERR		;25 is maximum wait
	RLC			;x 2
	MOV	C,A
	RLC			;x 4
	RLC			;x 8
	ADD	C		;x 10
	STA	WAITTM
WTSHOW:	CALL	ILPRT
	DB	'Wait time: ',TAB,0
	MVI	A,0		;clear HL
	MOV	L,A
	MOV	H,A
	LDA	WAITTM
SBLOOP: SUI	10		;div. by 10
	JC	WTDSP
	INR	L
	JMP	SBLOOP
WTDSP:	MVI	C,DECOUT
	CALL	MEX
	CALL	ILPRT
	DB	' seconds',CR,LF,0
;
; Compare next input-stream item in table @DE; CY=1
; if not found, else HL=matched data item
;
TSRCH:	MVI	C,LOOKUP	;get function code
	JMP	MEX		;pass to MEX processor
;
; Print in-line message ... blows away C register
;
ILPRT:	MVI	C,ILP		;get function code
	JMP	MEX		;go do it

;
; Sign-on message
;
SYSVER:	CALL	NITMOD
	LXI	D,SOMESG
	MVI	C,PRINT
	CALL	MEX
CARRSH:	LXI	D,NOMESG		;tell about carrier
	CALL	CARRCK			;check for it
	MVI	C,PRINT
	CNZ	MEX			;print the "NO" if no carrier
	LXI	D,CARMSG		;print "carrier present"
	MVI	C,PRINT
	CALL	MEX
	RET
;
;
	IF	SFTCRD
SOMESG: DB	'Apple II w/Microsoft Softcard',CR,LF
	ENDIF	;SFTCRD
;
;
	IF	ALSCRD
SOMESG: DB	'Apple II w/ALS CP/M 3.0 Card',CR,LF
	ENDIF	;ALSCRD
;
	IF	MM2E
	DB      'and Hayes Micromodem IIe',CR,LF,'$'
	ENDIF   ;MM2E
;
	IF NOT	MM2E
	DB	'and Hayes Micromodem II',CR,LF,'$'
	ENDIF	;NOT MM2E
NOMESG:	DB	'no $'
CARMSG:	DB	'carrier present',CR,LF,'$'
;
; CHECK THE MICROMODEM FOR CARRIER PRESENT (NZ=NO)
;
CARRCK:	CALL	XDATIN
	CALL	XSTTIN
	ANI	4
	RET
;
; Newline on console
;
CRLF:	MVI	A,CR
	CALL	TYPE
	MVI	A,LF		;fall into TYPE
;
; type char in A on console
;
TYPE:	PUSH	H		;save 'em
	PUSH	D
	PUSH	B
	MOV	E,A		;align output character
	MVI	C,CONOUT	;print via MEX
	CALL	MEX
	POP	B
	POP	D
	POP	H
	RET			   
;
; strings to clear-to-end-of-screen, and clear-screen
;
EOSMSG:	DB	ESC,'Y$'	;clear to end-of-screen
CLSMSG:	DB	ESC,'*$'	;clear whole screen

;-------------------------------------------------------
; Apple I/O 
;-------------------------------------------------------

	IF	SFTCRD

XDATOUT	STA	MODDAT ! RET
XCTLOUT	STA	MODCTL ! RET
XBDOUT	STA	BAUDRP ! RET
XONHOOK	STA	ONHOOK ! RET
XOFFHK	STA	OFFHOOK ! RET

XSTTIN	LDA	MODSTT ! RET
XDATIN	LDA	MODDAT ! RET
XCTLIN	LDA	MODCTL ! RET
XBDIN	LDA	BAUDRP ! RET
XCTL3	LDA	MODCTL3 ! RET

	ENDIF	

	IF ALSCRD
;
; ALS card routines require assembly with MAC
; (supplied with the ALS CP/M card)
; 
PUT	MACRO	ADDR
	PUSH	H
	LXI	H,ADDR
	JMP	APWRT
	ENDM
	   
XDATOUT	PUT	MODDAT
XCTLOUT	PUT	MODCTL
XBDOUT	PUT	BAUDRP
XONHOOK	PUT	ONHOOK
XOFFHK	PUT	OFFHOOK
XCTL3	PUT	MODCTL3

APWRT:	PUSH	D
	PUSH	B
AW0:	CALL	$-$	; patch vector here
	POP	B
	POP	D
	POP	H
	RET

GET	MACRO	ADDR
	PUSH	H
	LXI	H,ADDR
	JMP	APRD
	ENDM

XSTTIN	GET	MODSTT
XDATIN	GET	MODDAT
XCTLIN	GET	MODCTL
XBDIN	GET	BAUDRP

APRD:	PUSH	D
	PUSH	B
AR0:	CALL	$-$	; patch vector here
	POP	B
	POP	D
	POP	H
	RET

	ENDIF
;
;------------------------------------------------------------
;
	END
